The reviews are automatic translation.
When the wheel assembly work
On 2016-08-02 18:57:21
You can work without worrying about licking the nipple in the tetrahedral contact.
On 2016-08-02 18:15:20
Firm for us to hold the nipple.
It is easy to use if there is a sense of security is also a little bitter nipple.
On 2016-06-01 15:54:58
It is very easy to use.
Development of bicycle
On 2015-07-14 15:54:13
Purchase in order to challenge the hand Wheels.
This industry? In reputable this product,
When the hand set is now, but give it a try in the Wheels,
Put a spoke in the slit of the wrench for tetrahedral hold
It will be how to use, such as to sandwich the nipple from the top.
There is adequate clearance with respect to the nipple, around the spokes
Easy to turn curved surface processing is given.
Familiar person I like is used a good three-sided holding SW-2C of the work efficiency,
Both poor workability it is not to lick the nipple,
For beginners like me I think that good.
Proper use of the SW-2C of those who have a budget three sides hold would be best.
On 2015-06-11 07:52:47
In four sides hold, pat tightening can.
Bicycle spokes adjustment
On 2015-03-20 22:25:13
I spoke replacement of the bicycle, but when it comes to the final tensioning around, tension is becoming stronger, easier to lick it's aluminum nipple. At first, had been doing in cheap ring-shaped nipple once, became a middle becomes unusable interruption beginning to lick at the final adjustment. So I have also assured those with high, this product was choice. Without lick in aluminum nipple, it was able to be a tough tightening. And from the ring-shaped tool, because it does not come off when you are turning, it was easy to do not also drop. I think you want to select this product when the adjustment of the bike.
Assembly of the bicycle wheel (hobby)
On 2015-02-01 14:02:23
It is never wrong only because size.
Compared to the size combined type, it has become easy to hold shape.
In addition, since the hard out hard to lick the nipple, it can concentrate on work.
(Difficult to set the nipple than in the alternative some shared type)
As a whole, I think the most easy-to-use in the wrench that was used up to now.
To DT nipple turning
On 2015-01-28 16:02:42
It was purchased for DT aluminum nipple, but did not enter the nipple tightly.
Brass does not have to try, but in the 3.2mm of the nipple wrench in the nipple of 3.2mm I think that it is of course not enter because there is no gap.
You enter somehow be quite forcibly pushed into the nipple, the nipple does not become useless because would scraped full of scratches, is the price is easy to use and contains tightly better the following anonymous goods half.
By chance it might come off as of but only a higher price, I feel like a bad accuracy.
Since the spokes have been rusty, for the exchange work.
On 2014-02-02 21:45:53
Slightly larger gap in the nipple of ♯14. I want something a little more good accuracy.
I want things both are attached to both ends for general vehicles and sports cars ♯13 of ♯14. Because it is not for the business you must have good COSPA the general public.
It spoke Nanoha dissatisfaction only one set of 72 this selling.
Spoke length of the front wheels and the rear wheels are made to buy two sets of 144 so different, half is to be discarded at no use.
By all means we want you to sell a set of 36 selling.
Maintenance of the bicycle hand-wheel
On 2013-06-17 09:25:05
# Was purchased for 14, since it does not confuse than those corresponding to the various
Very easy to use
In addition, very good because it does not damage the also easy to over nipple torque