The reviews are automatic translation.
Showing 1 - 17 of 17 Reviews which have 5 star
[ See all 25 customer reviews ]
On 2017-05-21 20:50:48
I received it immediately very much, but the price was normal.
Carbide knife finish
On 2017-04-10 13:14:45
There is no problem to the product itself, the feeling of use is also good. But packing is disappointing. This time I bought two pieces of GC and WA red, whereas the WA red one was wrapped in cushioning material (bubble wrap), whereas this GC was a plastic with only one thin cardboard on one side. Thanks to this, there was a little dent as small finger nails on the side without cardboard. I will use it as it is because there is no problem on the purpose of this time, but I think that I am returning it for the purpose of severe polishing.
Polishing of metal products
On 2017-02-05 20:47:42
I did not sell it to the home center, and I could purchase it cheaply.
Polishing of carbide drill blades
On 2017-01-05 22:58:40
With the grinding stone attached to the grinder, the carbide drill blade (monotalou, detailed unknown) was not ground, so it was replaced with a GC grindstone. For GC grinding wheels, the carbide blade can be successfully grounded, but on the contrary, the high-speed blade and the cobalt high-speed blade are excessively ground and can not be finely adjusted (the high-speed blade which is thinner than approximately φ 4 has a contact portion at the time of contact with the grindstone It felt like disappearing).
On 2016-11-17 16:05:07
Especially None None None None in particular
On 2016-04-20 21:21:08
There is no particular problem.
On 2016-03-29 15:10:32
I installed it in the tabletop grinder I got. I contacted Monotaro with the mounting hole diameter and I admired the appropriate reply. The impression is neither good nor bad.
Cemented carbide, cermet byte sharpening
On 2015-10-15 21:00:05
I have not used anything other than Noritake, but I think that it is a good thing that there is not any dissatisfaction with this
On 2015-05-19 21:30:31
It is a pottery shop. I am using it for polishing the bottom of a pendant. It can be cut smoothly. Since there is a thickness, it is appreciated without sacrificing it.
For grinding of cutlery in general
On 2015-04-29 22:04:15
The maximum circumferential speed is about 20% higher than the general item, so you can raise the revolution by that much, so you can grind efficiently.
On 2014-09-30 13:39:17
For cutting hard objects
On 2014-07-22 00:57:03
It is cheaper and better than buying in the near field. For products, we think that there are other parties other than this other wheel.
It is used for grinding of cutting tools such as drills
On 2013-10-17 01:00:33
I always bought it from Monotarou. Price, quality, delivery time are satisfied with all. Thank you in the future.
On 2013-08-19 13:56:42
The size I was looking for was not found at all and finally arrived. It is handy with abundant kinds of handling. It was saved. Also, the price is also cheap. Thank you very much.
It is a shop. Metal, pendant etc, polishing of the internal part of the glaze of the baked product.
On 2013-07-12 17:06:02
After ordering, we corrected the mistake of shaft diameter and ordered again. It is a familiar product, and even if it is high in hardness, it is easy to polish and satisfactory. Thank you.
Carbide cutting tool grinding.
On 2013-04-16 21:04:26
It is used when sharpening a cemented carbide blade (byte) such as lathe cutting. A moderate hardness is good for sharpening a knife of hard material. After flattening the grindstone surface with a dresser, you can also finely grind the cutlery.
I use it for grinding scissors. It is a scissor used by a professional. Sharpen the scissors.
On 2011-08-13 14:38:48
This grinding stone is used as a rough grindstone that is absolutely indispensable. Bring to the spill of the blade, or the missing blade. Since I am well given down, work is fast. I do not mind eyes, I can use cheaply and at ease.