The reviews are automatic translation.
When dimension of product is measured
On 2016-12-21 16:44:30
We used other companies' products to measure the dimensions of the product, but changed to the one above and the cost drastically declined.
On 2016-08-17 17:27:03
When reading a scale of 0.1 mm, the gap of the overlapping line is large, so we can not confirm it. If the tolerance is ± 0.1, it can not be used.
Used for machining automobiles / bikes
On 2016-06-27 19:20:39
Since most of the special work is done, it is useful for fine dimensions etc. I am fine even with a monotaro brand.
Product processing time
On 2016-05-30 09:11:22
I am satisfied because it was able to purchase cheaply, as the precision did not change with those of other manufacturers.
On 2016-05-05 07:06:24
There is no problem in particular. As soon as the nail of the box cracks, it is inconvenient for storage.
On 2016-04-13 20:31:45
I am glad that the price is cheap
Engine parts measurement
On 2016-02-25 14:33:55
When the caliper's depth gauge deviates by 0.2 mm initial value, it is the one that I reported the previous time, but after that, it did not have any problem after confirming it well. I was overlooked a bit. I apologize to you.
On 2016-02-04 23:51:56
☆ It is not inferior to the first-class manufacturer made at the factory. It is enough for work at work that does not require precision precision.
Used for various measurements. Outside, internal measurement is a must - do thing.
On 2015-12-17 23:05:57
I should just purchase something a little bigger. Because I had something shorter than 5 cm.
Measurement of parts etc.
On 2015-12-09 17:32:22
Play compared to a certain maker item? Love? I felt doubt about the accuracy with large. Although it will be unsuitable for measurement of precise objects, since it seems that there is no problem for simple measurement such as residual amount measurement, we use it without dividing it.
On 2015-11-13 16:21:47
On 2015-10-11 14:46:32
It was good for price.
Motorcycle Maintenance etc.
On 2015-08-23 00:39:35
I appreciate it if there are graduations on both sides.
Golf club creation
On 2015-08-18 16:07:18
I found a desired item at a low price. Thank you very much
Dimension measurement of plate thickness
On 2015-08-11 14:33:40
At the second speed after purchase, the screw on the back of the caliper back has gone away from one side. Everything has gone, but then. . Because it is a very small special screw, there is no change easily. Also, you can not find it if you drop it. Just because the screws are gone, the core in the middle will be loose and it will not be usable. Because it is cheap, I think that it is good to use after attaching "screw loose stopper".
We will aim for size and thickness
On 2015-08-03 15:02:25
Thanks to the price, it was nice to be in a proper case. It was a good product because the point is sharp and dangerous.
On 2015-07-23 21:20:31
It is quite big. I think that it is enough for most applications even if it is one size small.
On 2015-06-05 15:21:36
That price is sufficient for that price
Measure the dimensions of items at sample planning room
On 2015-05-12 14:56:14
I wanted a larger caliper, so it was good to purchase at reasonable price. You can use it without any inferiorities to other companies' super expensive calipers.
On 2015-04-20 09:10:19
Parts used for bicycles are required for precision of 0.1 mm and therefore purchased for part size measurement. There is not much thing to calibrate, but it can be used without problems. The main body is a feeling that every edge is standing and it is scraped out. It is not so dangerous as to cut your finger but because it is dangerous, it is dropping the edge that is not related to measurement with waterproof paper. Purchase As soon as you look at the exterior, you can see a dent on the vernier scale. There is no problem in use, but I feel hurt. I would like to consider examining the inspection system.