The reviews are automatic translation.
Bleeding of bag
On 2018-06-21 13:49:39
It was finished neatly with the work of attaching eyelet as air hole of fabric bag.
To pull out the leather
On 2018-06-07 14:41:53
I can not get out of it at all, only as many times as I can hit the traces. This is the first time for punch. I want to return honestly · · ·
On 2018-06-02 14:04:40
Thankful that there is a big size, but no blades are attached, it took a considerable amount of time to be able to use it for sharpening. In this case it is better to buy things with blades even if it is a bit higher, without wasteful labor.
We are using it for drilling the clear sheet used for windmill making
On 2018-03-17 23:35:25
It is easy to fit in the center of the marker, and it is possible to smoothly punch out and it is satisfactory. Mott If you order quickly I was able to relax. I hope next time as well.
On 2017-11-27 17:56:34
Work efficiency sharply improved than what I used before.
On 2017-09-23 22:14:29
It is hard to make a hole a little. There are tricks. Work itself may be difficult for children.
On 2017-05-19 16:26:26
The sharpness of the cutting edge is bad. Can you cut out a piece of it?
Pull out the printed paper
On 2017-04-07 15:48:01
I bought two but there was a difference in sharpness. Although one can be used extensively, the other one can hardly come out even if you put your strength and hit it with a hammer. The sharpness was obviously different when touching the cutting edge. Because price is cheap, there is probably losing, but it is a shame.
I got the size which is not in the home center.
On 2017-02-19 13:46:15
Since the punch handled in the nearby home center does not deal with a small hole or a large hole punch, we purchased several items from 1 mm to 4 mm and from 25 mm to 30 mm here this time. I think that it is worth the price as well, and the sharpness is also good for ordinary. However, when it becomes a punch of 30 mm, it firmly fixes and it can not come off neatly unless it hits accurately with a large hammer as it is. The punch of 25mm - 30mm is trusted and is firmly indeed. I think that it is very good as a product.
On 2017-02-03 14:25:35
Because it is a punch used as a hobby, so much expensive things are unnecessary. However, when looking at the punch set at the home center, it will be set from roughly 5 mm in diameter. So I bought a total of 6 punch with a diameter of 1 mm to 4 mm with Monotaro. Sharpness is also sufficient, and it is worth the price as well. It was good.
When building the seat of the truck, punch the hole.
On 2016-05-13 23:20:19
Successfully, there was a hole.
Fuel pump packing production
On 2016-02-29 05:27:20
Yunbo's fuel pump malfunction, parts can not be obtained, packing defective air sucking state packing can not be successfully created, dropping ceremony was used for mounting on another tank but it stops due to insufficient capacity finally repaired with your tool you found it is complete. As long as the tank attached at the time of stoppage is used as a kerosene tank at the time of start, Tempura waste oil 99% power generation agriculture is carried out. Thank you very much.
Production of skin packing
On 2015-11-13 01:09:49
It is plural purchase, although there was a slight deformation, it is largely good.
On 2015-08-31 15:46:50
I think individual differences, but with the goods that arrived, the holes do not open in the leather. The punch blade is not attached at all. Punch which can not pierce is defective so I thought about return exchange, but I put a blade on my own. By the way leather that I tried to open was about 1 mm tanned skin, and even if I hit it, I could only break without breaking it. After cutting, you can punch only by pushing with a hand without tapping it.
Cut a circle from a color sheet
On 2015-06-29 21:19:27
Since we needed a small circular seal, we punched out and tried it. A circle seal can be made neatly without a needle hole in the center like a circle compass. Since there are various sizes, I would like to arrange it when it becomes necessary due to size difference in the future.
Drilling of aluminum thin plate
On 2014-10-16 19:15:22
I know I will hurt the tools. I tried doing it because other suitable method can not be used easily, but it seems to be able to use it for the time being as it is imagined. Price is cheap enough, even if it is disposable it is practical and satisfactory.