Buy more than* S$200* and get FREE SHIPPING

Magnetic Holding Base

Sort by:
Showing 1 - 30 of 228 Results
Show: 30 60 90
VIEW: Grid View List View
Neodymium Magnet Holder
TRUSCO
4.75(4)
11.99 - 32.99 SGD
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
35.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 200[20], Tapped-hole Processing: Available, Screw Holes for Mounting: M6, 10mm deep, Surface Processing: Coating, Dimensions (Length L x Width W x Height H) (mm): 60x26x25, Outside Dimension (depth D x Width W x Height H) (mm): 26x60x25, Weight (g): 250, TRUSCO Part Number: 107-6728, Others: *T-SHAPED HAND...
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
19.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 100[10], Tapped-hole Processing: Available, Screw Holes for Mounting: M6, deep, 8mm, Surface Processing: Coating, Outside Diameter x Height H (phi mm x mm): phi26x25, Weight (g): 80, TRUSCO Part Number: 107-6701
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder, Round
BeHAUS
4.67(3)
3.99 - 5.99 SGD
Caution: Keep away from clocks and PCs., Keep away from clocks and PCs., Purpose: Can be used as material such as steel plates, molds, jigs, tools, etc., Can be used as material such as steel plates, molds, jigs, tools, etc., Material: Anisotropic ferrite magnet, Accessories: Double sided tape
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder
TRUSCO
3.86(7)
2.99 - 5.99 SGD
Screw Dimensions: M4, Dimension (phi x Height H) (mm): 44x8, Weight (g): 54
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
50.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 500[50], Tapped-hole Processing: Available, Screw Holes for Mounting: M8 deep 12mm, Surface Processing: Painting coating, Outside Diameter x Height H (phi mm x mm): phi50x40, Weight (g): 500, TRUSCO Part Number: 107-6752
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder, With Handle
TRUSCO
3.00(3)
19.99 - 64.99 SGD
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder, Square
BeHAUS
4.00(2)
5.99 - 10.99 SGD
Caution: Keep away from clocks and PCs., Keep away from clocks and PCs., Purpose: Can be used as material such as steel plates, molds, jigs, tools, etc., Can be used as material such as steel plates, molds, jigs, tools, etc., Material: Anisotropic ferrite magnet, Accessories: Double sided tape
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
35.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 300[30], Tapped-hole Processing: Available, Screw Holes for Mounting: M8, 12mm deep, Surface Processing: Coating, Outside Diameter x Height H (phi mm x mm): phi40x30, Weight (g): 240, TRUSCO Part Number: 107-6744
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder
KANETEC
36.99 SGD
ADD TO CART
Purpose: For weight of diagram, ruler, and paper mold. Can be used by embedding into press die. For hold work while wire cut work., For weight of diagram, ruler, and paper mold. Can be used by embedding into press die. For hold work while wire cut work., Adsorption Strength (N [kgf]): 50[5], Screw Holes for Mounting: None, Surface Processing: Nickel-plated, Outside Diameter x Height H (phi mm x mm): phi18x8, Weight (g): 2.5, Specification: Rare earth samarium and cobalt magnet applied Adsorption power: 20 deg C = 100%, 100 deg C = 95%, 200 deg C = 85% Continuous use should be 150 deg C max. 200 deg C is acceptable only for short time use.
Category Magnetic Holding Base > Permanent Magnetic Holder
Electromagnetic Holder
KANETEC
5.00(1)
129.99 - 639.99 SGD
2014 TRUSCO Published Page: 1-0754
Category Magnetic Holding Base > Electromagnetic Holder
Permanent Magnetic Holder
MonotaRO
5.00(2)
9.99 SGD
Screw Holes for Mounting: Without, Surface Processing: Plating
Category Magnetic Holding Base > Permanent Magnetic Holder
For T Type Handle Km-03C
KANETEC
5.00(2)
2.99 - 3.99 SGD
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
28.99 SGD
ADD TO CART
Caution: T-shaped handle not included, T-shaped handle not included, Purpose: Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die Can be used to hold workpieces during wire cutting., Adsorption Strength (N [kgf]): 150[15], Tapped-hole Processing: Available, Screw Holes for Mounting: M6, 8mm deep, Surface Processing: Coating, Outside Diameter x Height H (phi mm x mm): phi30x25, Weight (g): 110, TRUSCO Part Number: 107-6736
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Magnetic Holder
KANETEC
22.99 SGD
ADD TO CART
Purpose: Presser for drawing, ruler, forming sheet. Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die. Can be used to hold workpieces during wire cutting., Presser for drawing, ruler, forming sheet. Screw hole on the back can be applied to a wider assembly jig. Can be used by fill in press die. Can be used to hold workpieces during wire cutting., 2014 TRUSCO Published Page: 1-0758, Adsorption Strength (N [kgf]): 100[10], Tapped-hole Processing: 3.0 to a depth of Y in the pilot hole on the back, Screw Holes for Mounting: None, Surface Processing: Paint, Outside Dimension (depth D x Width W x Height H) (mm): 26x26x25, Weight (g): 110, TRUSCO Part Number: 107-6710, Specification: Ferrite magnets application Given that suction ability is 100% at 20...
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder
KANETEC
5.00(1)
18.99 - 55.99 SGD
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Electromagnetic Holder Square type
KANETEC
1,049.99 SGD
ADD TO CART
Purpose: In a wide range from a variety of automation equipment to handle part of the industrial robot. It is suitable for adsorption of the case and a donut-shaped perforated work to adsorb small items from the corner of the container or the like., 2015 Trusco Published Pages: 1 0805, Dimensions (Width x Depth x Height)(mm): 50x50x50, Adsorption Ability (N): 250, Voltage (V): DC24, Current (A): 0.43, Weight (kg): 0.75, Dimension (mm): 50x50x50, TRUSCO Part Number: 406-3465
Category Magnetic Holding Base > Permanent Electromagnetic Holder
Heat resistant Clamp Meter
KANETEC
229.99 SGD
ADD TO CART
Purpose: To wiring and fixing of the small-diameter code of thermocouples and high-temperature location. Happy fixed in places where the tape can not be used. It can also be used as a temporary fixture for the tool and welding temperature measurement., 2015 Trusco Published Pages: 1 0811, Adsorption Ability (N): 196, Outside Diameter x Height H (phi mm x mm): 50x67, Weight (kg): 0.5, TRUSCO Part Number: 406-3775
Category Magnetic Holding Base > Permanent Magnetic Holder
Strong Magnet
SK
3.33(3)
19.99 - 50.99 SGD
Category Magnetic Holding Base > Permanent Magnetic Holder
Steel Magnet clip
SK
7.99 - 9.99 SGD
Category Magnetic Holding Base > Permanent Magnetic Holder
Plate Magnet
SK
42.99 SGD
ADD TO CART
Adsorption Ability (N): 59, Overall Width (mm): 52, Weight (g): 350, Overall Length (mm): 130, Thickness (mm): 15
Category Magnetic Holding Base > Permanent Magnetic Holder
Thin Magnetic Holder
KANETEC
409.99 - 539.99 SGD
Purpose: In a wide range from a variety of automation equipment to handle part of the industrial robot., 2015 Trusco Published Pages: 1 0804, Voltage (V): DC90, Height (mm): 30
Category Magnetic Holding Base > Electromagnetic Holder
Rectifier KR-T type for Electromagnetic Chuck
KANETEC
1,299.99 - 2,579.99 SGD
Purpose: It rectifies the input from the AC power supply to direct current, and then output to the electromagnetic chuck via a degausser. DC output is at a voltage variable, you can control the suction force of the electromagnetic chuck., Rated Output Voltage: DC 0-120V
Category Magnetic Holding Base > Electromagnetic Holder
Electromagnetic Holder Thin
TRUSCO
94.99 - 249.99 SGD
Caution: Specifications allowable temperature of electromagnetic holder, is peripheral 40degC ore less, object 50 degC or less. Max adsorbability depends on material, thickness, finishing conditions. Depends on object condition, there residual magnetism remains. T, Specifications allowable temperature of electromagnetic holder, is peripheral 40degC ore less, object 50 degC or less. Max adsorbability depends on material, thickness, finishing conditions. Depends on object condition, there residual magnetism remains. T, Purpose: As grip of various automation apparatus and industrial robots., As grip of various automation apparatus and industrial robots., 2014 TRUSCO Published Page: 1-0754
Category Magnetic Holding Base > Electromagnetic Holder
Permanent Magnet Holder Samarium cobalt magnet Round・Stainless type
KANETEC
33.99 - 65.99 SGD
Purpose: Drawings, ruler, such as the pressing of the paper type. To hold the wire cutting work during the work., 2015 Trusco Published Pages: 1 0809, Mounting Screw: -
Category Magnetic Holding Base > Permanent Magnetic Holder
Alnico Magnet
KANETEC
23.99 - 62.99 SGD
2015 Trusco Published Pages: 1 0810, Mounting Screw: -
Category Magnetic Holding Base > Permanent Magnetic Holder
Permanent Holder Mag Pad
KANETEC
75.99 - 109.99 SGD
Purpose: A wire electrode of a wire electric discharge machine, to protect from the release of easy cooling liquid to occur at the time of the start of processing, prevent heat generation disconnection due to air discharge equipment. Magupaddo is, the wire electro, 2015 Trusco Published Pages: 1 0811
Category Magnetic Holding Base > Permanent Magnetic Holder
Angle Clamp
KANETEC
339.99 SGD
ADD TO CART
Caution: A long period of time can not be used to work the application of heat. When applied to a high temperature in the magnet force is suddenly reduced or abolished and (demagnetized), there is a risk of adsorbates is out., Purpose: Can be used to temporarily assembled, the temporary holding of work and assembly with welding temporary, and strongly adsorbed and held. Moreover, it can also be used as a block., Adsorption Ability (N): 400, Weight (kg): 1
Category Magnetic Holding Base > Permanent Magnetic Holder
Magnet Holder
KANETEC
449.99 - 519.99 SGD
Caution: It can not be used to work for a long time applying heat ※. When applied to a high temperature in the magnet force is suddenly reduced or abolished and (demagnetized), there is a risk of adsorbates is out. ※ suction force of the iron plate, SS400, is the , Purpose: Can be used to temporarily assembled, the temporary holding of work and assembly with welding temporary, and strongly adsorbed and held.
Category Magnetic Holding Base > Permanent Magnetic Holder
T Handle Small
KANETEC
2.99 SGD
ADD TO CART
Category Magnetic Holding Base > Permanent Magnetic Holder

1 2 3 4 5 6 7 8 Next